ONVYRODIGITALScaling Brands. Optimizing Ads.
Home / Blog / Lower a high ACoS

PPC · 6 min read · By Hassan Iftikhar

How to lower a high ACoS without killing sales

Short answer: don't cut every bid at once. Find your break-even ACoS, remove spend that produces no orders, lower bids only where the numbers say so, adjust placements, and fix conversion. Waste goes first, sales that pay for themselves stay.

When ACoS is too high, the obvious move is to slash bids across the account. ACoS drops, and so do sales, organic rank and sometimes the business. A few weeks later the seller raises bids again, and the cycle repeats.

There's a better way. A high ACoS is almost never one problem. It's a mix of spend that does nothing and spend that is working but slightly overpriced. The trick is to cut the first and tune the second.

Step 1: Know what "high" means for this product

An ACoS is only high relative to the product's break-even. Take the price, subtract product cost and Amazon fees, and divide by the price. A product with a $30 price, $8 cost and $10 in fees has $12 left, so break-even ACoS is 40%. For that product, 35% is fine. For a product with half the margin, 35% loses money on every ad order.

Do this for each advertised product. You'll often find that the account average hides a few products far above break-even and others comfortably below.

Step 2: Cut spend that produces nothing

Start with the search term report for the last 30 to 60 days. Find terms with real spend and zero orders. Decide on a click threshold based on your conversion rate: if roughly one in ten clicks converts, a term with 25 clicks and no orders is very unlikely to turn around.

Add those terms as negatives, and check targets and keywords the same way. This step usually lowers ACoS without losing a single sale, because the spend you remove wasn't producing any.

Step 3: Lower bids where the maths says so

For keywords that do convert but run above break-even, work out what you can afford per click: break-even ACoS times price times conversion rate. If a keyword converts at 10% on a $30 product with a 40% break-even, the ceiling is $1.20. If you're paying $1.60, bring it down towards the ceiling in steps, and give each change a week or two before judging it.

Leave keywords that are below break-even alone, or even push them. Those are the sales you want more of.

Step 4: Check placements

Pull the placement report for each campaign. Top of search, rest of search and product pages often perform very differently. If product page placements are eating budget with poor returns, reduce them. If top of search converts strongly, a placement modifier can win more of it without raising every bid.

Step 5: Untangle overlapping campaigns

When the same search term is targeted in several campaigns, you can end up paying more than you need to, and it gets hard to see which bid is actually setting the price. Keep discovery in auto and broad campaigns, move proven terms into exact match, and add them as negatives where they were found so they're bought once, at the bid you chose.

Step 6: Fix conversion

If a product's ACoS is high on almost every keyword, the problem may be the listing, not the bids. A better main image, clearer bullets, a competitive price or a stronger review position all raise conversion, and higher conversion lowers ACoS at the same bids. We go through this in why your listing isn't converting.

Step 7: Watch total sales, not just ad sales

When you lower ACoS, keep an eye on total sales and TACoS, which is ad spend divided by total sales. If ad sales dip slightly but total sales hold, you were paying for sales you'd have got anyway. If total sales fall sharply, you may have cut something that was supporting organic rank, and you can add it back carefully.

How long it takes

Cutting waste shows up quickly, often within the first couple of weeks, because the spend simply stops. Bid and placement changes need more time to settle, and listing changes need enough traffic to judge. We plan in phases: waste in the first weeks, bids and structure in the first month or two, then conversion and growth.

Where to start

Work out break-even for your biggest-spending product and pull its search term report. If you find terms with spend and no orders, you've found the first part of the fix. If you'd like us to do it with you, our Red to Black plan is built for exactly this, and the free Profit Leak Check is a no-cost way to see where you stand.

More from the blog

Free Profit Leak Check

Want to know how far above break-even you are?

Send one product. We'll work out its break-even ACoS and show you the leaks, free.